#Minicom how to use serial
#Minicom how to use series

#Minicom how to use serial

NO G - Software Flow Control: NO Change with setting? Set the value of option A to / dev / ttyS0 to indicate serial port 1, if using serial port 2, set to / dev / ttyS1, and so on. Connect the router through serial port under linux to realize the function of super terminal. Select the Exit from minicom option to return to the command line from the configuration menu. Select the Save as df1 option to save the modified configuration information as the default configuration option. What needs to be modified is to remove A - initing string вЂ¦вЂ¦ :, B - Reset string вЂ¦вЂ¦: K - Hang-up stringвЂ¦ three configuration items. Setting Modem and dialing Use the directional arrows to select the modem and dialing item, then modify the configuration items in the modem and dialing option. The use of commands in the setting process, for example, you need to modify the value of option A, in Change with setting? Enter A after the option to move the cursor to the A option, you can modify the value of the A option. Set the value (baud rate) of option E to 115200. Set serial port setup Use the down arrow to select serial port setup, and the configuration of each option appears: A - Serial Device: / dev / ttyS0 B - lockfile Location: / var / lock C - Calling Program: D - Callout Program: E - Bps / par / Bits: 115200 8N1 F - Hardware Flow Control: NO G - Software Flow Control: NO Change with setting? Set the value of option A to / dev / ttyS0 means serial port 1, if serial port 2 is used, set to / dev / ttyS1, and so on. After the configuration is complete, select Save setup as df1, and then use minicom later Use the command minicom вЂ“s, the following interface appears on the screen: вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ Filename and paths вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦ File transfer and protocols вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦ Serial port setup вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦ Modem and dialing вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦ Screen and keyboard вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦ Save setup as df1 вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦ Save setup as вЂ¦вЂ¦ вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ Exit вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦ Exit from minicom вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦вЂ¦ 2. Generally, the first time you start, you need to use the command minicom вЂ“s to configure minicom. Use the command minicom вЂ“s to start minicom. Configure minicom and use minicom 1пјЋStart minicom Log in to the system with root privileges. The development board I used is the TE2 2440II board. Use CTRL+A S to enter file sending menu and select xmodem by pressing Enter.Mount version older than kernel RPC Call returned error 101 and other error messages, it is very convenient to use minicom, but the first time you use minicom, you need to make settings. Open minicom, reset board and make sure Transfer mode is UART XMODEM. Uploading using UART method uses XMODEM protocol to upload program. Find BOOT SEL Switch from Board pin mapping.

Upload mode is set using BOOT SEL Switch.

Follow the method supported by your target board. VEGA SDK supports many methods for uploading program. bin file to the target board and executing that file on target board. While uploading, we are transferring the. Please send file using XMODEM and then press ENTER key.

#Minicom how to use series

VEGA Series of Microprocessors Developed By C-DAC, INDIAД«ootloader, ver 1.0.0 Wed Aug 19 17:40: #70]